Screen Printing Machine for Hard Material Caps with Plate & Resin for Hat Printing

  

Screen Printing Machine for Hard Material Caps w/ Plate & Resin for Hat Printing. This machine is designed for printing on various hard material caps, such as safety helmets and motorcycle helmets.

It can enhance printing quality and efficiency significantly. Printing on hard material caps poses challenges due to their rigid and varied shapes, making accurate positioning difficult and resulting in low printing efficiency and quality. Our screen printing machine addresses these challenges effectively. Hat Bottom Positioning: The shaping resin ensures stable positioning of the hat bottom, accommodating any material and shape accurately. Lower Hat Positioning: Secondary four-point positioning at the lower part of the hat prevents movement during printing, ensuring easy removal and precise positioning.

Stainless Steel Cambered Plate: The plate can bend slightly to match the hat's arc, ensuring parallel alignment for accurate printing. The platform and positioning platform are movable with a drag positioning device for precise placement. The stainless steel plate features a large magnetic area for stable positioning. Manual knobs allow micro-adjustments in multiple directions for precise printing.

The machine accommodates various cap shapes with two flexible stainless steel frames. The shaping resin facilitates hat positioning and can be heated multiple times for reuse. The bottom of the stainless steel plate is equipped with a large area of magnetic plate, which can be directly adsorbed on the platform. You can push and pull the plate with a little force to move on the platform (screws and nuts can also be installed in the 8 long holes on the platform after positioning the plate to block the four sides of the plate for more stable positioning). The main machine can be micro adjusted by manual knobs from left to right, up and down, up and down can move 170 mm; There is with a handle lock; Left and right can adjust 20mm, tighten and lock.

The machine adopts 1 mm stainless steel plate, the screen frame directly fixed on both sides of the frame beam; Screen plate can move 130mm front and rear; Screen plate installation beam can finished by adjusting the screen radian by hand screw; After adjusting to the same radian as the printing surface, lock the screws at both ends of the two beams. The shaping resin has the characteristics of softening by heating and hardening by cooling; After heating to 60-100 degrees Celsius, the resin softens, place and press the bottom of the hat into the resin; After the resin cools and hardens, remove the hat, leave the outer contour shape of the hat inside the resin, and complete the positioning of the bottom. This type of resin can be repeatedly heated and cooled (user can choose electric oven heating or high temperature hot air gun heating, also can use our company supporting SPE- arc screen special heating drying cabinet).

The machine is equipped with two flexible stainless steel frames; Inner size is 100190 mm (outer size is 130200 mm); 100240 mm (outer size 130250 mm); Suitable for most kinds of hard hat printing patterns. All parts of the machine are advanced electrostatic spraying surface treatment, corrosion resistance, acid and alkali resistance, cleaning resistance, long - term use without rust. Supporting equipment of the machine (optional according to the need, details of supporting equipment see the relevant webpage): SPE-3040 special stretcher for arc-surface screen plate: due to the softness of arc-surface screen plate, normal stretcher cannot be used; This stretcher is specialized in stretching mesh of arc screen plate; It can stretch 2 arc screen plates with the outer size of 130250 mm at the same time. SPE- cambered screen plate special coating emulsion machine: because the arc screen plate of stainless steel only 1 mm thick, edge only 15 mm, relatively soft, traditional coating photosensitive emulsion can not ensure the smooth coating, the machine is specially designed for the arc screen plate, only used with the screen plate matching. SPE-arc screen plate special drying cabinet: this machine is used for two purposes: one is specially drying the arc screen plate after degreasing and cleaning ; The second is used to heating the soft resin.

SPE-4632SBJ exposure unit: cambered screen plate can be suitable for a variety of exposure unit ; This exposure unit is not a special supporting equipment. This machine can place 3 cambered screen plate at the same time with the out side of 130250 mm. Heating the shaping resin until soft and put it on the lower platform of the machine; And push into the machine to position; 2. Install the screen frame with blank mesh on the frame rack; 3. Cover the bottom of the hat with teflon cloth and press it into the shaping resin, adjust the radian of the screen frame and the printing arc of the hat, and basically determine the position of the printing pattern on the screen; 4.

Adjust the positioning position of the hat, and push the soft resin beside to the four sides of the hat by hand to strengthen and fix; 5. After the resin is cooled, hold the four positioning handles of the second-floor platform against the four fixing points in the lower part of the hat and lock them.

Take out the hat, take out the teflon cloth, the hat positioning is completed (special note: after the positioning is completed, do not move the positioning resin tray). Take down the screen plate and make plate according to the position of the pattern; 8.

In order to prevent ink overflow, screen plate around can be affixed with sealing strip; 9. Install the finished screen plate and adjust it to the appropriate position, Install the fixed screws on both sides of the screen plate to lock and print. SPE-AQM240 One Color Safety Helmet Hard Material Caps Screen Printing Machine 1.

Orders are processed from Monday-Friday; Not on the weekends & public holidays. We will work with you to get the case resolved in the fastest method. Please contact with us at first for more details.

If product was received damaged or not as described, please send us some pictures or videos, so we could well understand your problem, then solve them for you ASAP. Besides, it's much helpful for us to claim with UPS, remind our related department to pay much more attention to packaging later on. If an item is received damaged, customer service must be contacted within 7 days of receiving your item. ECheck Issues: Payments via eCheck do not clear immediately.

Usually you will wait 5-7 days after checkout for it to clear.