, Mugs, Beer Mugs, Wine Glasses and Other Cups; Glass Tubes, Pens, Ballpoint Pens, Fishing Rods, Bats and Other Small Cylindrical Products. For Cylindrical and Conical Products, the Printing Surface Has Large Depressions or Protrusions, and There Are Non-planar Pits in the Printing Surface, Which Is Not Suitable for Printing by This Machine. This Curved Screen Printing Machine Is Mainly Used for Printing. Cylindrical and Conical Products with a Diameter of. Install the Screen Frame and Adjust to the Suitable Height, Install the Handle Position According to Using Habit.Install the Squeegee and Fix It at a Distance of 1-2 Cm from the Pattern. Adjust the Position of the Printing Frame and Roller Bearing, Place the Printing Object on Wheel and Leave some Spac Between the Screen Frame. Make Sure the Printing Object If Line up with the Squeegee. Adjust the Screen Frame Position and Pour out Ink. The Machine Adopts a Left-right Push-pull Structure; the Mounting Parts Can Be Adjusted According to Needs, Suitable for Left-handed or Right-handed Operation; Suitable for Printing Height 200 Mm; Length 150 Mm Within the Pattern; Suitable for Outer Diameter 260 450 Mm, Thickness 35 Mm the Use of a Kind of Stencil. 2, the Machine Adjusts and Positions the Height of the Rear Main Frame. The Rear Main Beam Is Adjusted up and down According to the Height of the Substrate by Adjusting the Post Screw.
The up and down Adjustment Range Is 200 Mm. It Can Print Cylindrical and Conical Products with a Diameter of 170 Mm. The Printing Frame of the Substrate Is Designed to Move Forward and Backward, and the Three Fixed Aluminum Strips at the Bottom Are Directly Installed on the Base. The Aluminum Strip Can Move 290 Mm from Side to Side; Positioning Bracket Mounting Strip.The Three Mounting Strips Can Be Moved Left and Right As Needed, and They Are Locked in 19 U-shaped Holes at the Front and Back of the Base (Each Hole Is 15 Mm Apart) to Ensure Accurate Positioning of the Mounting Strips. Displacement of the Mounting bar: Loosen the Two Screws of the Mounting bar, Push the Mounting bar to the Rear of the Machine to the Long Hole, Move the Mounting bar to the Left and Right, and Then Move the Mounting bar to the Fixed U-shaped Slot, Tighten the Two Screws Positioning Is Complete. 4, Three Sets of Substrates Are Used to Place the Rollers, Which Are Metal Bearing Rollers (Diameter 19 Mm); Nylon Bearing Rollers (Diameter 25 Mm); Plastic Bearing Rollers (Diameter 50 Mm), Which Can Be Replaced by Users As Needed.
Three Rollers Can Be Installed on the Main Frame and the Accessory Frame. The Bearing Mounting Frame Is Directly Fixed in the Mounting Hole of the Aluminum Strip, and Can Move up and down 160 Mm According to the Height of the Substrate.
4 Additional Mounting Brackets, Remove the Bearings on the Original Main Mounting Bracket, and Directly Fix the Additional Mounting Bracket on the Main Mounting with Screws, Mainly Used for the Printing of Conical Products. The Additional Mounting Bracket Can Be Moved up and down by 20 Mm. Feedback is very important to us. It is impossible to address issues if we do not know about them!
Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount.Due to time zones, our reply to your questions may not be immediately. If it's non-workdays, please kindly be patient and wait till Monday. This item is in the category "Business & Industrial\Printing & Graphic Arts\Screen & Specialty Printing\Screen Printing". The seller is "ycmjwangluo22" and is located in this country: US. This item can be shipped to United States.